PLUMBING PROBLEMS
Leak under the sink: finding it and fixing it
Where water under a sink usually comes from, a simple way to find the source, and what to do before a plumber arrives.
IN SHORT
Most leaks under a sink come from one of four places: the waste trap, the joint where the sink drains into it, the flexible pipes feeding the tap, or a washing machine or dishwasher hose. Dry everything, put down kitchen roll, then run the tap and drain the sink separately to see which one drips. A waste leak only happens when water drains; a supply leak drips even when nothing is running.
This page is part of our guide to common plumbing problems.
If water is spraying or pouring, turn it off first. Look for an isolation valve on the pipe feeding the tap: turn the slot a quarter turn so it sits across the pipe. If there isn't one, turn off the stop tap, usually under the kitchen sink or where the water pipe enters the house. If water is near electrics, keep away and switch off at the fuse box if it's safe to reach.
Where the water usually comes from
There are four usual suspects in the cupboard under a sink.
- The trap. The U-shaped or bottle-shaped plastic fitting under the plughole. Its nuts work loose and its seals wear.
- The waste outlet. Where the sink itself drains into the trap. The seal under the plughole can perish over time.
- The tap connectors. Most modern taps are fed by two flexible braided pipes. They can leak at the joints, or wear out with age.
- Appliance hoses. A washing machine or dishwasher often connects under the sink, to a water valve and to the trap.
How to find the source
Empty and dry it
Clear the cupboard, dry every pipe and joint with a towel, and put kitchen roll on the cupboard floor.
Wait without using anything
Leave it for 15 minutes. If it drips with nothing running, it's on the supply side: a tap connector, a valve or an appliance feed. Those pipes are always under pressure.
Run the tap, plug out
If it only drips while water drains away, the leak is on the waste side: the trap or the outlet seal.
Fill the sink and let it go
A full sink draining pushes more water through the waste at once and shows slow leaks a running tap might miss.
Run the appliance
If nothing else drips, run the washing machine or dishwasher and watch its hoses and connections.
Running a dry finger or a piece of tissue along each joint helps pinpoint the exact spot.
What you can safely try
- Hand-tighten plastic trap nuts. Often that's all it takes. Don't use tools on plastic fittings: they crack.
- Re-seat an appliance hose if it has pulled loose from the trap spigot.
- Check for condensation. Cold pipes in a warm kitchen can sweat. That shows as droplets along the pipe, not a drip from one joint.
Leave anything involving the supply pipes, valves or tap connectors to a plumber unless you're confident, because those are under mains pressure.
When to call a plumber
- The leak is on the supply side, or from a valve.
- Tightening the trap hasn't stopped it, and a seal needs replacing.
- The cupboard floor or the wall behind is soft or stained, which means it's been leaking for a while.
Most under-sink leaks are short jobs. If the tap itself is the problem, see what a new kitchen tap costs. If an appliance needs reconnecting, see plumbing in a washing machine.
A slow leak under the sink is the kind of job Fill My Day is built for: needs doing, doesn't need doing this minute. It's coming soon to Bristol and isn't taking bookings yet. See what's launching in Bristol.
GOOD TO KNOW
Questions,
answered straight.
Why is there water under my sink?
Usually a loose or worn joint on the waste trap, a perished seal where the sink drains into it, a leaking flexible tap connector, or an appliance hose. Sometimes it's condensation on a cold pipe, which forms droplets but never a steady drip.
Is a leak under the sink an emergency?
A slow drip into a cupboard isn't, though it's worth fixing soon to stop damage. Water spraying from a pipe is: turn off the isolation valve or the stop tap straight away.
Can I tighten a leaking sink trap myself?
Plastic trap nuts can usually be hand-tightened, and often that's all it needs. Don't use tools on plastic fittings, as they crack easily. If tightening doesn't stop it, the seal inside may need replacing.
Who do I call for a leak under the sink?
A plumber. If the leak is from a washing machine or dishwasher itself rather than its hose or connection, you may need an appliance engineer instead.
FIRST STOP / BRISTOL
Bristol.
You’re up first.
The app is in development and isn't taking bookings yet. Plumbers first, other trades to follow.